12-volt 25-amp pull switch for cars and motorbikes
2-pole pull switch 25 amps
Technical specifications:
- Operating voltage: 2 to 28 volts
- Maximum acceptable current: 25 amps
- Self-holding in position
- Temperature range: -30°C to +90°C
- Installation hole diameter: 10mm
- Tightness: IP65
| Weight | 0,1 kg |
|---|
You may also like…
-
Relays and fusesReversing relay 12 volts 150 Amperes 6 poles
150-amp reversing relay:
- 4×4 winch
- Boat ink lift motor
- Fans
- Acceptable power: 1800 watts
- Operating voltage: 9-16V
- Operating temperature: -30°C to + 110°C
- To be used with a 3 terminal switch
-
We recommend using high-power fuses with this type of relay
-
Switches and switch padsPush button starter switch 12V 50 amps, with soft rubber cap
Momentary push button:
- Widely used for starter and horn
- Contact type: Momentary
- Max current: 50 amps
- No need for relays
- IP55 sealing
- 2 screw terminals for connection
- NO contact: Normally open
2 reviews -
Switches and switch padsPDM Switch Pad 6 round switches 25 amps 12 volts Discount Autosport 3D Printed
PDM-style 6-switch board:
- Switch Pad look
- 6-colour LED backlighting
- Up to 20 amps / switch
- Dimensions: 100 x 80 mm
- Rigid 3D printed board
- Temperature range: -20°C to +115°C
- Total weight: 110 grams
- Supplied with 2 screws with GOLD anodised washers + nuts and washers
-
Simple, reliable and cost-effective
-
Switches and switch pads12V 25 Amp “Toggle Switch” for electrical circuits
12V ON / OFF switch:
- Max voltage: 48 volts
- Silver inner contact
- Supplied with rubber cap
- 4.8mm flat terminals
-
Max current: 25 amps
3 reviews
Related products
-
Switches and switch padsPower distribution box with 12 PDM 12 volt switch board for complete wiring harness
Power distribution box + 12-switch board
- Supplied with resettable circuit breaker
- Switch Panel” look like a PDM
- 6-colour LED backlighting
- Up to 30 amps / switch
- Temperature range: -40°C to +85°C
- Tightness: IP67
- Supplied with full wiring diagram
- Simple, reliable and cost-effective
-
Equip your car like a factory WRC car or endurance prototype
-
Switches and switch padsBlue CNC starter plate 8 round aluminium switches PDM look “Switch Panel” 25 amps 12 volts
Machined aluminium 8-switch board:
- 7 fixed, 1 momentary
- Switch Panel” look like a PDM
- 4-colour LED backlighting
- Up to 25 amps / switch
- Dimensions: 140 x 80 mm
- 5-axis machined plate in 6061 aluminium
- Temperature range: -40°C to +90°C
- Total weight: 200 grams
- Tightness: IP67
- Supplied with 2 countersunk screws + nuts and washers
- Supplied with full wiring diagram
-
Simple, reliable and cost-effective
-
Switches and switch padsFIA Cut Off switch electronic 180 amps 12 volts FIA approved waterproof IP67
180 amp electronic circuit breaker:
- Circuit breaker controlled by 2 switches
- Can be fitted in place of a conventional circuit breaker
- Simple, reliable installation (no on-board electronics)
- IP67 sealed switches
- IP67 sealing (Fully sealed)
- Operating voltage: 6 to 48 volts
- Brand: Discount Autosport
- Designed, developed and assembled in-house
- Wiring diagram included
-
Delivered as a complete kit
1 review -
Switches and switch padsResistor for circuit breaker / battery 10 watts 3 ohm CNC machined body gold
Circuit breaker resistor:
- 3 ohm resistor
- 10 watts
- 6 to 24 volts
- CNC machined
- Gold anodised
- Drilled for mounting
- Lugs drilled to accept soldering wire
2 reviews
