Switches and switch pads
Showing 1–12 of 31 results
-
Switches and switch pads12V 25 Amp “Toggle Switch” for electrical circuits
12V ON / OFF switch:
- Max voltage: 48 volts
- Silver inner contact
- Supplied with rubber cap
- 4.8mm flat terminals
-
Max current: 25 amps
(0 reviews) -
Switches and switch padsPolarity reversing lever switch 6 terminals 12 volts
12-volt reversing switch:
- 3 positions ON – OFF – ON
- Self-holding in position
- Voltage range: 2 to 250 volts
- Maximum current: 15 amps
- Temperature range: -30°C to +90°C
- Installation hole diameter: 12mm
- Tightness: IP65
-
3 positions with dead centre
(0 reviews) -
Switches and switch padsPush button starter switch 12V 50 amps, with soft rubber cap
Momentary push button:
- Widely used for starter and horn
- Contact type: Momentary
- Max current: 50 amps
- No need for relays
- IP55 sealing
- 2 screw terminals for connection
- NO contact: Normally open
(0 reviews) -
Switches and switch padsResistor for circuit breaker / battery 10 watts 3 ohm CNC machined body gold
Circuit breaker resistor:
- 3 ohm resistor
- 10 watts
- 6 to 24 volts
- CNC machined
- Gold anodised
- Drilled for mounting
- Lugs drilled to accept soldering wire
(0 reviews) -
Switches and switch padsElectronic circuit breaker 180 amps 12 volts FIA approved waterproof IP67
180 amp electronic circuit breaker:
- Circuit breaker controlled by 2 switches
- Can be fitted in place of a conventional circuit breaker
- Simple, reliable installation (no on-board electronics)
- IP67 sealed switches
- IP67 sealing (Fully sealed)
- Operating voltage: 6 to 48 volts
- Brand: Discount Autosport
- Designed, developed and assembled in-house
- Wiring diagram included
-
Delivered as a complete kit
(0 reviews) -
Switches and switch padsResistor in porcelain for 12V circuit breaker 10 watts 3.3 ohm
Circuit breaker resistor:
- 3.3 ohm resistor
- 10 watts
- 6 to 24 volts
- Porcelain body
(0 reviews) -
Switches and switch pads4 switch starter plate 25 amps 12 volts Discount Autosport 3D Printed
4-switch starter board :
- 3 fixed, 1 momentary
- Simple and easy to install
- Up to 25 amps / switch
- 48 volts maximum
- Dimensions: 140 x 50 mm
- Rigid 3D printed circuit board
- Temperature range: -40°C to +90°C
- Total weight: 150 grams
- Tightness: IP64
- Supplied with 2 countersunk screws + nuts and washers
-
Simple, reliable and cost-effective
(0 reviews) -
Switches and switch pads75-amp 12-volt high-power switch
High-power switch:
- Operating voltage: 2 to 28 volts
- Auto hold in position
- Temperature range: -30°C to +60°C
- Installation hole diameter: 10mm
- Tightness: IP65
- M5 terminals
-
Maximum current: 75 amps
(0 reviews) -
Switches and switch pads8 round switch panel PDM look “Switch Panel” 25 amps 12 volts Discount Autosport 3D Printed
8-switch board, PDM look:
- 7 fixed, 1 momentary
- Switch Panel” look like a PDM
- 4-colour LED backlighting
- Up to 20 amps / switch
- Dimensions: 140 x 80 mm
- Rigid 3D printed circuit board
- Temperature range: -40°C to +90°C
- Total weight: 150 grams
- Tightness: IP67
- Supplied with 2 countersunk screws + nuts and washers
-
Simple, reliable and cost-effective
(0 reviews) -
Switches and switch padsEngine start button for Japanese motocross bikes Yamaha, Kawasaki, Suzuki, Honda
Motorbike starter button:
- Operating voltage: 0 to 28 volts
- Maximum acceptable current: 20 amps
- Momentary button
- Temperature range: -30°C to +90°C
- Diameter of standard motorbike handlebar clamp
- 30cm long harness with PVC sheath
- For Japanese motocross bikes
-
Yamaha, Kawasaki, Suzuki, Honda
(0 reviews) -
Switches and switch padsStarter switch and ignition key 12 volts 30 amps
Key-operated starter switch:
- Operating voltage: 2 to 28 volts
- Maximum acceptable current: 30 amps
- Self-locking in position
- Temperature range: -30°C to +90°C
- Installation hole diameter: 24mm
- Supplied with 2 keys
-
Connection with 4 terminals on back
(0 reviews) -
Switches and switch padsPush button engine start LED starter switch 12V 50 amps
Engine Start button:
- Widely used for starter
- Contact type: Momentary
- Max current: 50 amps
- No need for relays
- IP55 sealing
- 2 screw terminals for connection
- NO contact: Normally open
-
LED backlight
(0 reviews)
